HOW TO MAKE A BEDINI MONOPOLE ENERGIZER PDF

5. Newsletter. Before doing anything else, make sure to sign up for the free Energy .. Bedini Mono-Pole Energizer circuit that is extremely similar to the diagram. WHAT IS THE BEDINI SG? Get a copy of the Bedini SG – The Authorized Beginner’s Manual if you want to learn all about the Bedini SG and how to build your. This is a hands-on explanation of how to build a monopole energizer based on John C. Bedini’s patent No. 6,, This system charges lead acid or gel cell.

Author: Vikazahn Nikolar
Country: Thailand
Language: English (Spanish)
Genre: Business
Published (Last): 18 June 2017
Pages: 332
PDF File Size: 19.52 Mb
ePub File Size: 11.6 Mb
ISBN: 211-4-63682-440-7
Downloads: 54670
Price: Free* [*Free Regsitration Required]
Uploader: Gardanris

If the voltage is higher than 1 volt, or the resistor gets hot, then adjust the base resistance potentiometer. Measure the voltage of the charging battery and note the amps reading on the analog amp meter. This also ties in with the field reversing in the drive core too possibly an attempt to get at least a weak push off this reversal monopoke appreciable generator action.

Specifications – Trigger wire: All along Keelynet was given the information. Put a voltmeter across the light bulb.

Bedini SSG Monopole Energizer Motor Kit

This motor energizer is energixer mechanical oscillator whose speed depends on the lowest amount of current you can put into the coil. Members are encouraged to record their Monopole SSG build information in this database. Reluctance Motors, Bedini Advancedmessages extracted from http: It also provides additional references to related theory and advancement beyond this starting point.

Record the voltage of the battery after it has rested in the “End Resting Voltage” field in the Input Joules section in the table.

  COMCAST NGOD PDF

John Bedini Monopole Generators

The resistance of the coil is not important, the windings are not important, the magnets are not important. Save those old junk car starter batteries bedii later.

Neon Lamp Purpose – The lamp provides a path for the output energy in case the receiving battery is disconnected while the motor is running.

Specifications – 1 K ohms, 2 watt. Use a voltmeter to measure voltage across the 1Q resistance. One thing to keep in mind is that what Nonopole Bedini said during the filming may or may not be what he holds today.

Only an insignificant amount of conventional charging could take place with the arrangement in the schematic circuit diagram. The destination hlw reach a charge capacity of 14 volts at 1: Find all posts by selamatg.

Lead-acid batteries are rated for a hour discharge. Find all posts by Bodkins. Mount the rotor to the frame, ensure that the rotor spins freely. This voltage should be no lower than Bedini has been known to use a Hall Sensor.

I know that several of you on Keelynet tried very hard to build this motor, but I said in the beginning, just build the motor the way I said to do it. Also to maintain wires to prevent snagging. If you work during the day and want to sleep at night, choose a cycle that allows you enough time to charge and discharge. Snail ;5ea of itoan bilb cad be left or remcrcd r. None of this type of energy can be found in the textbooks we have today, although it has been around long before text books!

This opens the Bloch Wall – the place in the center of the magnet where the energy comes from.

To s the article above use: The source battery and the secondary battery being charged are NEVER directly connected to each other. Next, figure out how much time you have to collect data. This will come into play later, so for now, as hard as it is, just try and forget it. It is said that this is the setup neccessary to swap the batteries indefinatly as it converts the output of the coils into a form of energy that is better suited to run inductive loads than direct output into the vedini.

  IEC 60095 1 PDF

Make sure that each wire does not differ more than 3 gauges apart. It also helps us hiw that there are two kinds of energy going to the charging battery.

This forum is for educational purposes only.

John Bedini Monopole Generators :: Nikola TESLA 3 generations later

Quantity – One length of each wire, about ” 30mm Magnets Purpose – To attach to the outside of the rotor, in order to maintain rotation and provide an induced voltage on the trigger wire to befini the transistor.

I’ve ruminated long and hard over the ‘SSG is more advanced than the capacitor version’ quote myself and having built a variety of Bedini machines, I’m not convinced. There is a learning process here for those who built this motor the way I said to do it about ten people. Replace the potentiometer with a fixed value resistor. Measure the current and write it down as the “Load Amps in the Output Joules section of the table.